Casting Kits

Piston Rings

The Stuart Triple is a very accurate model of a marine steam engine. It comes complete with working reverse gear, feed pump and condenser vacuum pump and is ideal for a scale steamer or tug, being a delight to watch under steam.

The Stuart Triple is one of the most complex models in our range, however the time and effort is well invested as it is also one of the most attractive. Many of these engines are kept as display models, whilst others are built into dioramas recreating the engine room of a steam liner or large launch.

Height: 6 Inches.
Discwheel Diameter: 2 1/4 Inches.
Cylinder Bores: 3/4 Inch, 1 1/4 Inches & 1 3/4 Inches.
Cylinder Stroke: 1 Inch.

Cast Iron: Soleplate, cylinder castings, valve chests and covers, top and bottom cylinder covers, pistons, eccentric sheaves, counter balance weights, discwheel.

Gunmetal: Slider bracket, connecting rod bearings, eccentric rods, slide valves, air pump castings,
feed pump castings, stuffing box, glands, crossheads, crankshaft bearings.

Sundries: Detailed drawings, cylinder lagging, gasket material, piston rings, gland packing, fixings pack.

Click on picture for large view.

Stuart Pain Set both Green and Black Paint

Small steam and exhaust pipe set.

Stuart Finished cylinder pipe work.

Oil Cups

This boiler is offered in 1/12 scale to go with our machine shop tools. The boiler is constructed of copper and the firebox is steel with 14 aluminum castings consisting of the following: front, back, door frame, 6 doors, 4 draft knobs and a stack transit

Click on picture for large view of kit.

Put life into your steam engines, run them on live steam. What a sight! This boiler will easily run one of our well constructed #2, #3 or #5 steam engines for light-duty use and demonstration purposes.

Popular around the turn of the century because of their simplicity and small floor space.

Click on picture for large view of kit.

Water Cooled Red Wing Motor 1/4 Scale - Engine Casting Kit

Bore 1-1/2", Stroke 2", Gasoline Engine

The 5 HP Red Wing Engine was the inspiration for this fully functional quarter scale model.It runs on regular gasoline and uses a buzz coil as an ignition source.

This bronze and iron engine comes with 10 bronze castings and 9 iron castings and several small parts such as springs, gears, piston rings and other small parts needed to build your engine along with a complete set of working drawings.

This is a casting kit that requires a lathe and a mill to complete.

Click on picture for large view of Castings.

Related Products:

Oak Buzz Coil $168.95

Detailed Machining Directions for The Red Wing Hit & Miss Engine $19.95

Drain Cock 3/16 - 40 $26.50

Air Cooled Red Wing Motor 1/3 Scale - Engine Casting Kit

Bore 1-1/2", Stroke 2", Gasoline Engine

The 2.5 HP air cooled Red Wing Engine was the inspiration for this fully functional one third scale model. It runs on regular gasoline and uses a buzz coil as an ignition source.

This bronze and iron engine comes with 10 bronze castings and 11 iron castings and several small parts such as springs, gears, piston rings and other small parts needed to build your engine along with a complete set of working drawings.

This is a casting kit that requires a lathe and a mill to complete.

Click on picture for large view.

Related Products:

Oak Buzz Coil $168.95

Drain Cock 3/16 - 40 $26.50

Galloway - 1/3 Scale of 5 HP Hit and Miss Engine

Galloway Water Cooled 1/3 Scale Model Hit and Miss Engine Casting Kit

Kit Contains:

Cast Iron Castings (8)
2 flywheels, base, bearing caps, cylinder, cylinder sleeve, head, and water hopper

Bronze Castings (9)
Conn. rod block, igniter, igniter trip, push rod brackets, governor bracket, carburetor, rocker arm bracket, muffler top and bottom

Aluminum Castings (1)
Piston

Detailed Blueprints (7) 17" x 22", Set of Gears (Exact width, bore, and one with shallow keyway)

Optional Cast Iron: Sub-base is now included!

Galloway Model Specifications:
Flywheels - 10.200 inch
Bore Diameter - 1.750 inch
Stroke - 3.375 inch

These kits are castings that must be machined.

Shipping weight 80 lbs. Galloway Paint: Dulux 93-066-H Red

NOTE: WE HAVE RE-DRAWN THE PLANS TO THIS ENGINE IN AUTO CADE. WE HAVE CORRECTED ALL MISTAKES THAT WERE PREVIOUSLY FOUND IN THE ORIGINAL SHELLY DRAWINGS.



Click on picture for large view.

Related Products:

Galloway 1-3 Scale Ignitor Finished $200.00

Galloway 1-3 Scale Mixer Finished $200.00

Wooden Base for 1-3 Galloway Hit & Miss Engine with Electronics $368.80

Galloway - 1/3 Scale of 5 HP Hit and Miss Engine

Galloway Water Cooled 1/3 Scale Model Hit and Miss Engine Machined Kit

Kit Contains: ALL machined parts for the Galloway 1/3 hit and miss engine. You have to paint the engine make the coil and supply battery and fuel to run your engine. Wooden base not included.

Galloway Model Specifications:
Flywheels - 10.200 inch
Bore Diameter - 1.750 inch
Stroke - 3.375 inch

Shipping weight 68 lbs. Galloway Paint: Dulux 93-066-H Red

Note: Wood base is not included. This item must be purchased seperatly.



Click on picture for large view.

Related Products:

Wooden Base for 1-3 Galloway Hit & Miss Engine with Electronics $368.80

Galloway - 1/4 Scale of 5 HP Hit and Miss Engine With NEW CAD DRAWINGS. All of the Galloway casting kits have redrawn plans. The errors have been removed.

Galloway Water Cooled 1/4 Scale Model Hit and Miss Engine Casting Kit

Kit Contains:

Cast Iron Castings (8)
2 flywheels, base, bearing caps, cylinder, cylinder sleeve, head and sub-base

Bronze Castings (9)
Connecting rod bearing, carburetor, igniter, push rod brackets, governor bracket, rocker arm bracket, muffler top and muffler bottom.

Aluminum Castings (2)
Water hopper and Piston

Set of Gears (Bored to size)
Detailed Blueprints (5) 17" x 22", (3) 1 ½" x 14", (1) 8 ½" x 11"

¼ Scale Galloway Specifications:
Flywheels - 7.625 inch
Bore - 1.312 inch
Stroke - 2.530 inch

A lathe and milling machine are needed to finish the castings and to fabricate the additional parts required.

Shipping Weight 37 lbs. Galloway Paint: Dulux 93-066-H Red

NOTE: An Investment Cast Steel Crankshaft cast from a lost wax pattern is available separately. This is available for the ¼ scale Galloway only. (crankshaft must be machined). Available Separately See Below.



Click on picture for large view.

Galloway 1/4 Scale 3D PDF Picture

Related Products:

Galloway 1/4 Scale Model Hit and Miss Engine Casting Kit $49.95

Galloway 1-4 Scale Ignitor Finished $200.00

Galloway 1-4 Scale Mixer Finished $200.00

Wooden Base for 1-4 Galloway Hit & Miss Engine with Electronics $368.80

Galloway - 1/4 Scale of 5 HP Hit and Miss Engine

This is a lost wax casting for the 1/4 Galloway Crank

Click on picture for large view.

Galloway - 1/6 Scale of 5 HP Hit and Miss Engine

Galloway Water Cooled 1/6 Scale Model Hit and Miss Engine Casting Kit

NOTE: WE HAVE RE-DRAWN THE PLANS TO THIS ENGINE IN AUTO CADE. WE HAVE CORRECTED ALL MISTAKES THAT WERE PREVIOUSLY FOUND IN THE ORIGINAL SHELLY DRAWINGS.

Galloway Paint: Dulux 93-066-H Red

Click on picture for large view.

Related Products:

Wooden Base for 1-6 Galloway Hit & Miss Engine with Electronics $368.80

Galloway - 1/8 Scale of 5 HP Hit and Miss Engine

Galloway Water Cooled 1/8 Scale Model Hit and Miss Engine Casting Kit

Flywheel 3.82" Bore .623" Stroke .625"

Galloway Paint: Dulux 93-066-H Red

Click on picture for large view.

Related Products:

Wooden Base for 1-8 Galloway Hit & Miss Engine with Electronics $368.80

Scale Model of a Woodpecker Hit and Miss Engine - Casting Kit

Kit Contains:

Cast Iron Castings (6)
Base, Head, Bearing blocks, Cylinder sleeve, 2 Flywheels

Aluminum Castings (3)
Sub-base, Waterhopper, and Piston

Bronze Castings (9)
Rocker Arm Bracket, A & B Governor Weights, Cam Lever, Rocker Arm, Governor Lock, Connecting Rod, Muffler Top and Muffler Bottom

Other Items
Set of Gears, Blueprints (7), Spring (Makes 3 springs)

Woodpecker Model Specifications:
Flywheels - 6.375 inch
Stroke - 1.937 inch
Bore - 1.312 inch

Foundry castings that must be machined.

Shipping Weight 33 lbs.

Paint: Dulux - V7738 Hunter Green



Click on picture for large view.

Schafer's Little York Hit and Miss Casting Kit

Kit Contains:

Aluminum Castings (3)
Base, head and fender

Cast Iron Castings (6)
2 flywheels, cylinder, 2 valve cages, and piston

Bronze Castings (9)
Conn. rod, rocker arm, timing arm, 2 gov. weights, gov. brackets, arm retainer, speed adjustable block and camshaft bearing

Set of Boston Gears
Photographs (2)
Detailed Blueprints (4) 17" x 22"

Schaefer Model Specifications:
Flywheels - 4 ½ inch
Bore - .750 inch
Stroke - 1.50 inch

A lathe and milling machine are needed to finish the castings and to fabricate the additional parts required.

Shipping weight 10 lbs.

Paint: Dulux - 51907 Navy Blue



Click on picture for large view.

Paul Breisch Lil Brother Air Cooled Hit and Miss Casting Kit

Kit Contains:

Aluminum Castings (1)
Piston

Cast Iron Castings (7)
2 Flywheels, Cylinder Cap, Base, Air Cooled Cylinder, Bearing Caps

Set of Boston Gears
Detailed Blueprints
Name Plate

Little Brother Model Specifications:
Flywheels - 4 ½ inch
Bore - .750 inch
Stroke - 1.0 inch

A lathe and milling machine are needed to finish the castings and to fabricate the additional parts required.

Shipping weight 10 lbs.

Click on picture for large view.

Paul Breisch Lil Brother Air Cooled Hit and Miss Casting Kit

Kit Contains:

Aluminum Castings (1)
Piston

Cast Iron Castings (7)
2 Flywheels, Cylinder Cap, Base, Water Hopper, Bearing Caps

Set of Boston Gears
Detailed Blueprints
Name Plate

Little Brother Model Specifications:
Flywheels - 4 ½ inch
Bore - .750 inch
Stroke - 1.0 inch

A lathe and milling machine are needed to finish the castings and to fabricate the additional parts required.

Shipping weight 10 lbs.



Click on picture for large view.

1/4 Scale Olds Hit and Miss Casting Kit

Kit Contains:

Aluminum Castings (1)
Piston

Cast Iron Castings (5)
2 Flywheels, Cylinder Head, Base and Water Hopper, Bearing Caps

Bronz (2)
Connecting Rod, Igniter Trip

Detailed Blueprints

Model Specifications:
Flywheels - 4 ½ inch
Bore - .875 inch
Stroke - 1.125 inch

A lathe and milling machine are needed to finish the castings and to fabricate the additional parts required.

Shipping weight 10 lbs.

Also Needed:
Coles Power Models QTY
Connecting Rod Oiler - VR/2 1
Crankshaft Oiler - 29R2/3 2
3/16-40 M+P Brass Elbow 1
1/4-40 M+P Brass Nipple (Close 3/8) 1
Union Cock for 1/8" Tube Water Drain - 29L7/1 1
Piston Ring 1/16 X 7/8 3
Spark Plug 1/4-32 NGK 1

Local Purchase
Battery and Switch 1

Boston Gears
Crank Gear - Y2418 1
Cam Gear - Y2436 1

Springs (Century Spring Company)
Intake - S-60 1
Exhaust - S-794 1
Mixing Valve - DD-3 1
Timer Return - ZZI-25 1
Governor Control - N-15 1

S+S Ignitions
CDI-W/T Lite 1
Clip for Y4-32 Plug 1
Magnet 3/32 X 3/32 Round 1
Hall Futaba 1
Fut.Bat W-f 1

Click on picture for large view.

Machine Drawings of Schaeffer's Little York Model Hit and Miss Engine

These drawings have been completely redrawn in CAD. All errors have been corrected from Shelly's original designs. If you have an old set of drawings save some headaches and purchase these up to date plans.

Click on picture for large view.

Machine Drawings to Build Scale Model of a Woodpecker Hit and Miss Engine

These drawings have been completely redrawn in CAD. All errors have been corrected from Shelly's original designs. If you have an old set of drawings save some headaches and purchase these up to date plans.

Click on picture for large view.

Machine Drawings for the Galloway 1/3 Scale Model Hit and Miss Engine

These drawings have been completely redrawn in CAD. All errors have been corrected from Shelly's original designs. If you have an old set of drawings save some headaches and purchase these up to date plans.

Click on picture for large view.

Machine Drawings for the Galloway 1/4 Scale Model Hit and Miss Engine.

These drawings have been completely redrawn in CAD. All errors have been corrected from Shelly's original designs. If you have an old set of drawings save some headaches and purchase these up to date plans.

Click on picture for large view.

Machine Drawings for the Galloway 1/6 Scale Model Hit and Miss Engine

These drawings have been completely redrawn in CAD. All errors have been corrected from Shelly's original designs. If you have an old set of drawings save some headaches and purchase these up to date plans.

Click on picture for large view.

Machine Drawings for the Galloway 1/8 Scale Model Hit and Miss Engine

These drawings have been completely redrawn in CAD. All errors have been corrected from Shelly's original designs. If you have an old set of drawings save some headaches and purchase these up to date plans.

Click on picture for large view.

1903 De Dion casting kit with Gears.

The "De Dion 1903" from Classic Motors is a detailed copy of one of the first car engines built in large numbers. It is in scale 1:4 ; has much tourque at low revvs and is therefore a very good choice for a scale car of this period. This slow running 17cc fourstroke engine has an automatic inlet valve and an exhaust valve operated by a single cam. It runs excellent on 2-stroke mixture and can be used with spark ignition or glow ignition.

There are available casting kits including: castings for crankcase, cylinder, timing case, flywheels (bronce) and material for liner (nearly perfect inside) and piston ;gears and drawings are included. Also available is a CD with over 100 photos of building the De Dion. A very good help as you see each detail and assembly.

Bore x stroke 25mm x 30mm; app 180mm high.

Click on picture for large view.

Hubbard casting kit.

Scale replica of a marine engine from 1912. Capacity 12cc, flywheeldia. 85mm. runs at 1000 RPM, glowplug, suitable for beginners.

Click on picture for large view.

1909 Mercedes casting kit with gears.

Scale ca. 1:6, Capacity: 30cc, bore/stroke 20x25mm, 600 - 3000RPM, liquid cooled, glow ignition, lenght 230mm.

Click on picture for large view.

1895 Otto casting kit with gears.

The OTTO / Deutz stationary engine from 1895 is now available. This engine is a scale copy of the famous type D2. Depending on what carborator you build for this engine you can run it on clean propane or regular gasoline. You will be fascinated watching the engine running at low 150 RPM. Flywheeldiameter 200mm .

Click on picture for large view.

1895 Otto Deutz Model Engine Finished. Limited edition of only 12 made by the designer.

The OTTO / Deutz stationary engine from 1895 is now available. This engine is a scale copy of the famous type D2. This engine has a carborator that will run the OTTO on regular gasoline. You will be fascinated watching the engine running at low 150 RPM. Flywheeldiameter 200mm .

Click on picture for large view.