Online Catalogue
Start of Content
Shop By ProductVideos of EnginesStationary Steam EnginesTraction Steam EnginesSteam Powered Fire TrucksSteam Cars, Vans, etc.Stirling EnginesTurbine EnginesFlame EaterSteam LayoutsKitsPartsSteam AccessoriesFuel, Oil & BeltsSale! Click Here!Museum Quality EnginesBoats - Marine EnginesInternal Combustion EnginesTrainsTin ToysBoilersCasting KitsBurners and BeltsBooks and VideosErector Eitech SetsAntiques and Collectible Steam Engines and AccessoriesHand Made Steam Model Boats RC Radio ControlledConley V8 Model Engines How They are MadeRailroad Memorabilia and Technical Literature
Shop By ManufacturerWilescoJensenMamodBohm Stirling EnginesMSM Marine EnginesTucher & WaltherKrick Model BoatsConley ModelsClassic MotorsHistoric SteamSteamCo EnginesHielscherMaier Butane Powered Model EnginesBlechspielzeugSchucoMarklinHit and Miss EngineMaxitrakMarkieWiggersGyroscopePM Research Steam EnginesMSS Steam ToysHOG Desktop Stirling EnginesKarsten Steam EnginesCheddar Steam EnginesGerman Steam CarouselMaxwell HemmensLou Racioppo Private CollectionLiney Steam EnginesLow Temperature StirlingD.R. Mercer EnginesNochErector SetsEsbit and Oil

Parts - Heaters:

Online Catalogue | Jensen | Jensen | Steam Engine Parts | Steam Engine Parts |  Parts - Heaters:

Heater Mount Screws

Heater Mount Screws

Ref: JN101


Price:$0.20

Quantity:


Jensen Heater Element 110 volt A/C. (Without Power Cord 2.5 in Dia Boiler).

Jensen Heater Element 110 volt A/C. (Without Power Cord 2.5 in Dia Boiler).

Ref: JN081


Price:$34.95

Quantity:


Jensen Heater Element 110 volt A/C. (Without Power Cord 2.5 in Dia Boiler).

Instructions for Installing a Jensen Heating Element
Take the boiler and firebox assembly off of the metal base or board. Leave the boiler & boiler straps on the firebox.
Take off the insulation metal support by removing the 4 rivets. This can be accomplished in several ways:
Drilling out the rivets
Chiseling the rivets off from the inside
Use a Dremel tool to grind the 4 rivets out

Install the heater element, start both screws in the heater element to firebox, equally tighten these screws in order to gap the terminals so they do not touch the walls of the firebox. If terminals touch the firebox walls it will cause a dead short.
Next put in the 2 fire insulation sheets.
Now install the fiber insulation metal support with screws & nuts provided. You may also use a pop rivet gun if you do not want to use the screws & nuts.
Screw down the firebox & smoke stack support to the metal base or board.
Now put on the Hayco (cord restraint) with a pair of pliers or needle nose pliers. Place the smallest part of the Hayco restraint at the bottom of the power cord and press both sides of Hayco as close to smoke stack support as you can. Now pop the attached Hayco into the hole on the smoke stack support.
NOTE: ONLY FACTORY INSTALLED HEATER ELEMENTS ARE UNDER WARRANTY.
Click on This Text for Assembly and Operating Instructions

Jensen Heater Element 110 volt A/C. (With Power Cord 2.5 in Dia Boiler).

Jensen Heater Element 110 volt A/C. (With Power Cord 2.5 in Dia Boiler).

Ref: JN082


Price:$41.55

Quantity:


Jensen Heater Element 110 volt A/C. (With Power Cord 2.5 in Dia Boiler).
Click on This Text for Assembly and Operating Instructions

Jensen Heater Element 110 volt A/C  (Without Power Cord 3 in Dia.Boiler).

Jensen Heater Element 110 volt A/C (Without Power Cord 3 in Dia.Boiler).

Ref: JN083


Price:$52.95

Quantity:


Jensen Heater Element 110 volt A/C (Without Power Cord 3 in Dia.Boiler).
Click on This Text for Assembly and Operating Instructions

Jensen Heater Element 110 volt A/C  (With Power Cord 3 in Dia.Boiler).

Jensen Heater Element 110 volt A/C (With Power Cord 3 in Dia.Boiler).

Ref: JN084


Price:$59.98

Quantity:


Jensen Heater Element 110 volt A/C (With Power Cord 3 in Dia.Boiler).
Click on This Text for Assembly and Operating Instructions

Online Catalogue | Jensen | Jensen | Steam Engine Parts | Steam Engine Parts |  Parts - Heaters:

Main Pages

spacer
End of Content